Welcome to our Mining equipment manufacturing base, Contact Us


The gyratory crusher has capacities starting from 1200 to above 5000 t/h. To have a feed opening corresponding to that of a jaw crusher, the primary gyratory crusher must be much taller and heavier. Therefore, primary gyratories require quite a massive foundation. The cone crusher is a modified gyratory crusher.


Gyratory Crushers Gyratory crusher is generally used as a primary crusher. The crusher is popular due to its high throughput capacity and the large sized opening. The crusher is well suited for handling direct feed from haul/dump trucks. The gyratory crusher is mainly used in rock that is abrasive and/or has high compressive strength.


The bevel gear and pinion of the crusher are both of a cyclo-palloid spiral type, which allows greater forces to be absorbed and greater drive power to be installed. A B C C D F E I J H K G Gyratory crusher Weights 1) Type Feed opening Mantle diameter (oversized) Speed of eccentric bushing Max. motor power Total weight of gyratory crusher ...


The gyratory crusher at Sloan Quarry is capable of processing up to 1,300 tons of material per hour, taking it down from 12-inch plus to 8-inch minus rock.


About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features Press Copyright Contact us Creators ...


Gyratory crushers can accept 8–10% moisture in operation, but the fine content should be preferably less than 10%. The crushing action in gyratory crushers is regarded as rings or 'helics' (spirals) of feed down through the crusher of which a single section may be regarded as similar to the jaw crusher.


John R Kueneman Kueneman Don Original Assignee John R Kueneman Kueneman Don Priority date (The priority date is an assumption and is not a legal conclusion. Google has not performed a legal analysis and makes no representation as to the accuracy of the date listed.) ... Bearing seals for gyratory crushers US858130A US3080126A ()


Material is dumped into the primary gyratory crusher at Aggregate Industries' (member of LafargeHolcim) Morrison Quarry in Colorado.


Gyratory Crusher – Traylor 1000 TPH Primary Gyratory Crusher. 1000 TPH Primary Gyratory Crushing Plant Item #1 – Fuller-Traylor Model 42-70 Type TCB Gyratory Crusher with cast steel two piece mainframe, 400 h.p. – 4,000 volt electric motor, direct shaft drive, hydraulic su...


Get More Information

2. GYRATORY CRUSHERS

GYRATORY CRUSHERS The original patent for the gyratory crusher was granted to Phile- tus W. Gates in 1881. This fint crusher was used by the Buffalo Cement Co. At the time these early gyratory crushers were developed all mining and quarrying, either underground or open pit, was done by hand; tonnages generally were small and product ...


Gyratory Crushers. The primary rock breaker most commonly used in large plants is the gyratory crusher, of which a typical section is shown in Fig. 5. It consists essentially of a gyrating crushing head (521) working inside a crushing bowl (522) which is fixed to the frame (501).


Figure 5.1 Schematic diagram of a crusher showingg the open- and closed-side settings. 5.1 Jaw and Gyratory Crushers. Jaw and gyratory crushers are used mostly for primary crushing. They are characterized by wide gape and narrow discharge and are designed to handle large quantities of material. The capacity of the crusher is determined by its size.


HGT Gyratory Crusher. HGT Hydraulic Gyratory Crusher is a primary crushing equipment with high performance. It takes many advantages of high crushing efficiency, low production ... John Whitelong. Senior engineer. Veronique Smith. Senior engineer. Chris Zimerman. Senior engineer. Mary Villalonga. Senior engineer. ABOUT.


Gyratory crushers were invented by Charles Brown in 1877 and further developed by Gates in 1881 (they were commonly referred to as a 'Gate's crushers' in the early years). A primary crusher is designed to receive run-on-mine (ROM) rocks directly from the mines.


Diagram of a gyratory crusher [image: 135-5-16)] Gyratory Crushing Action. Designs of the breaking faces vary with manufacturer. As a result, the product size distribution varies. When the feed drops into the crusher, the mantle squeezes the rock against the concave surface.


The gyratory crusher includes a bowl which defines a chamber for receiving material to be crushed and a discharge opening at the base thereof through which crushed material is able to discharge. A crushing head is mounted in the bowl at an offset position with respect to a central axis of the bowl, and a drive assembly is operable for driving the crushing head within the bowl for imparting ...